NDT / PCN-NDT / CSWIP / AWS / API / QAQC -MECH,CIVIL,ELEC /CIVIL- NDT / MEP - HVAC/ SAFETY / SIX SIGMA / ISO AUDITOR - TRAINING AND CERTIFICATION...

RADIOGRAPHIC TESTING IN CHENNAI
 
 
 
 
Radiographic Testing (RT), or industrial radiography, is a nondestructive testing (NDT) method of inspecting materials for hidden flaws by using the ability of shortwavelength electromagnetic radiation (high energy photons) to penetrate various materials.

Either an X-ray machine or a radioactive source, like Ir-192, Co-60, or in rarer cases Cs-137 are used in a X-ray computed tomography machine as a source of photons.Neutron radiographic testing (NR) is a variant of radiographic testing which uses neutrons instead of photons to penetrate materials. This can see very different things from X-rays, because neutrons can pass with ease through lead and steel but are stopped by plastics, water and oils.

Since the amount of radiation emerging from the opposite side of the material can be detected and measured, variations in this amount (or intensity) of radiation are used to determine thickness or composition of material. Penetrating radiations are those restricted to that part of the electromagnetic spectrum of wavelength less than about 10nanometres.

The beam of radiation must be directed to the middle of the section under examination and must be normal to the material surface at that point, except in special techniques where known defects are best revealed by a different alignment of the beam. The length of weld under examination for each exposure shall be such that the thickness of the material at the diagnostic extremities, measured in the direction of the incident beam, does not exceed the actual thickness at that point by more than 6%. The specimen to be inspected is placed between the source of radiation and the detecting device, usually the film in a light tight holder or cassette, and the radiation is allowed to penetrate the part for the required length of time to be adequately recorded.

The result is a two-dimensional projection of the part onto the film, producing a latent image of varying densities according to the amount of radiation reaching each area. It is known as a radio graph, as distinct from a photograph produced by light. Because film is cumulative in its response (the exposure increasing as it absorbs more radiation), relatively weak radiation can be detected by prolonging the exposure until the film can record an image that will be visible after development. The radiograph is examined as a negative, without printing as a positive as in photography. This is because, in printing, some of the detail is always lost and no useful purpose is served.

Before commencing a radiographic examination, it is always advisable to examine the component with one's own eyes, to eliminate any possible external defects. If the surface of a weld is too irregular, it may be desirable to grind it to obtain a smooth finish, but this is likely to be limited to those cases in which the surface irregularities (which will be visible on the radio graph) may make detecting internal defects difficult.

After this visual examination, the operator will have a clear idea of the possibilities of access to the two faces of the weld, which is important both for the setting up of the equipment and for the choice of the most appropriate technique.

Defects such as delaminations and planar cracks are difficult to detect using radiography, particularly to the untrained eye. Without overlooking the negatives of radiographic inspection, Radiography does hold many significant benefits over ultrasonics, particularly insomuch that as a 'picture' is produced, more accurate identification of the defect can be made, and by more interpreters. Very important as most construction standards permit some level of defect acceptance, depending on the type and size of the defect.

To the trained Radiographer, subtle variations in visible film density provide the technician the ability to not only accurately locate a defect, but identify its type, size and location; an interpretation that can be physically reviewed and confirmed by others, possibly eliminating the need for expensive and unnecessary repairs.

Radiographic Testing - Benefits
  • Can inspect assembled components
  • Minimum surface preparation required
  • Detects both surface and subsurface defects
  • Provides a permanent record of the inspection
  • Verify internal flaws on complex structures
  • Isolate and inspect internal components
  • Automatically detect and measure internal flaws
  • Measure dimensions and angles within the sample
  • without sectioning
  • Sensitive to changes in thickness, corrosion, flaws and material density changes

Radiographic Testing - Application
Radiographic Testing is widely used in the;
  • Aerospace industries
  • Military defence
  • Offshore industries
  • Marine industries
  • Power-gen industries
  • Petrochem industries
  • Waste Management
  • Automotive industries
  • Manufacturing industries
  • Transport industries

NDT TRAINING INSTITUTE IN CHENNAI |PCN NDT TRAINING IN INDIA|CSWIP TRAINING IN INDIA |CSWIP WELDING COURSE 3.0,3.1,3.2 IN INDIA |NDT TRAINING IN CHENNAI | CSWIP TRAINING IN TRICHY |PCN NDT INSTITUTE IN CHENNAL |AWS WELDING INSTITUTE |QAQC CERTIFICATION|NDT IN INDIA |PCN COURSE IN CHENNAI |NDT TRAINING IN COIMBATORE | CSWIP WELDING COURSE| PCN NDT IN TAMIL NADU| PCN NDT COURSE| PCN NDT TRAINING INSTITUTE IN CHENNAI| PCN TRAINING AND CERTIFICATION IN INDIA | CSWIP WELDING TRAINING AND CERTIFICATION IN INDIA| NDT COCHIN | NDT IN VIZAG| NDT KERALA | NDT COCHIN | NDT INSTITUTE IN COCHIN| NDT TRAINING IN COCHIN| QA/QC INSPECTOR TRAINING IN KERALA| NDT TRAINING IN BANGALORE| AWS-CWI IN KERALA| NDT TRAINING IN COIMBATORE| NDT TRAINING IN TRICHY| NDT TRAINING IN CHENNAI| API TRAINING IN CHENNAI| AWS-CWI TRAINING COIMBATORE| API INSPECTOR TRAINING IN INDIA| AWS|AWS INDIA| AWS – CWIIN INDIA| NDT TRAINING IN CHENNAI INDIA| CSWIP CERTIFICATION| NDT CERTIFICATION| NDT LEVEL 2| ASNT LEVEL II| NDT TRAINING| CHENNAI, TRICHY, COIMBATORE, COCHIN, INDIA,TWGGROUP IN CHENNAI, CSWIP TRICHY, NDTTRICHY, AEROSPACE TRAINING IN CHENNAI, NDT COCHIN, CSWIP COIMBATORE,CIVIL NDT TRAINING IN CHENNAI | NDT TRAINING IN COCHIN| QA/QC INSPECTOR TRAINING IN KERALA| NDT TRAINING IN BANGALORE| AWS-CWI IN KERALA| NDT TRAINING IN COIMBATORE| NDT TRAINING IN TRICHY| NDT TRAINING IN CHENNAI| API TRAINING IN CHENNAI| AWS-CWI TRAINING COIMBATORE| API INSPECTOR TRAINING IN INDIA| AWS|AWS INDIA| AWS – CWIIN INDIA| NDT TRAINING IN CHENNAI INDIA| CSWIP CERTIFICATION| NDT CERTIFICATION| NDT LEVEL 2| ASNT LEVEL II| NDT TRAINING| CHENNAI, TRICHY, COIMBATORE, COCHIN, INDIA,TWGGROUP IN CHENNAI, CSWIP TRICHY, NDTTRICHY, AEROSPACE TRAINING IN CHENNAI, NDT COCHIN, CSWIP COIMBATORE,CIVIL NDT TRAINING IN CHENNAI | CSWIP TRAINING IN TRICHY |PCN NDT INSTITUTE IN CHENNAL |AWS WELDING INSTITUTE |QAQC CERTIFICATION|NDT IN INDIA |PCN COURSE IN CHENNAI |NDT TRAINING IN COIMBATORE | CSWIP WELDING COURSE| PCN NDT IN TAMIL NADU| PCN NDT COURSE| PCN NDT TRAINING INSTITUTE IN CHENNAI| PCN TRAINING AND CERTIFICATION IN INDIA |PCN NDT INSTITUTE IN CHENNAL